Door Skin Machine TM2480M
You are here: Home » Products » Vacuum Press Machine for Door » Door Skin Machine TM2480M

Product Detail

loading

Share to:
sharethis sharing button

Door Skin Machine TM2480M

General Introduction

This machine can be used to paste PVC on furniture, cabinets, speakers, relief doors, decoration panels for walls and other abnormal decoration shapes. With a special silicon sheet, it can also work with hot transfer and veneer.
Availability:
Quantity:
  • TM-2480M

  • ZHT

Door Skin Machine TM2480M


bfc5ae816600fab2dfb3493862790ab


1. Specification

1、 Model              TM2480M

2、 Dimension        10300MM×1920MM×1730MM

3、 Worktable size 2550(2350)MM×1150MM×40MM

4、 Maximum working surface
           2550(2350) MM×1150MM×40MM

5、 Maximum height of workpiece          60MM

6、 Total power                           15KW

7、 Actual power consumption               5KW

8、 Total weight                    2000(2500)KG

9、 Vacuum level ≥       -0.095Mpa to -0.08Mpa



TM series vacuum laminating machine is an economical and practical vacuum laminating equipment designed and manufactured by our company on the basis of absorbing advanced technology and experience from abroad. The machine can laminate various kinds of PVC masks on various shapes of substrates, such as imitation wood, stone, leather, etc.

After years of production practice and experience, our TM type laminating machine adopts German vacuum technology and chooses domestic 2X series vacuum pump with excellent performance and electric motor as the core of power. The machine is compact and easy to operate, the heating bin is light and easy to move, and there are two kinds of working tables of different sizes to use different widths of masks. The processing time of the workpiece, processing temperature and vacuum degree in the bin are automatically controlled by digital display, thus ensuring the quality of the product and improving the production efficiency and the finished product rate.

According to the needs, our company has manual, semi-automatic, automatic and single table, double table, full width, full narrow and one wide and one narrow table series products for customers to choose.

In recent years, our products have started to be exported to Southeast Asia, Russia, Canada and other countries and regions under the human approval of customers.

Note: Optional German vacuum pump is available.





 Workpiece processing technology

1, molding processing parts to pay attention to the surface of the workpiece to be laminated to sand, remove the surface of the wood chips and residues.

2、In order to achieve good lamination effect, rounded or beveled corners are recommended for the edges of the workpiece and the bottom of the molding.

3, the workpiece lamination part of the glue spraying to be uniform, not leak empty.

4、The glue sprayed workpiece must be dried before entering the laminating process for processing.

5、The workpiece should be placed on the workbench to maintain the corresponding distance (generally more than 2 times the height of the workpiece) to avoid the rupture of the PVC film caused by suction coating, resulting in scrap.

6、Avoid sharp workpieces from damaging the PVC film during the operation.

7、The workpiece should be padded with a pad, and the pad thickness and the thickness of the workpiece should be approximately the same, the pad surface should be slightly smaller than the workpiece 5MM, the pad should be flat, otherwise the workpiece will be fractured and cause scrap due to the large suction force during the suction, the pad should have good air permeability.

8, due to the PVC film leakage caused by the processing of individual parts of the film is not good, available transparent tape to seal the hole, and then sent to the work of the warehouse temperature absorption, individual places such as the glue is not dry caused by the absorption of bad, available electric hair dryer to heat repair.

9、After the workpiece is processed, the excess PVC film is cut off with a paper cutter.



TM2480A001        tm2480A002

 door   97332cf158937674ca3a0618fa2314c

 

8. Equipment maintenance requirements

1. Keep the inside of the workbench clean to prevent dust from entering the vacuum machine.

2. Keep the vacuum pipeline unblocked.

3. Frequently check the oil volume of the vacuum pump, replenish it in time, replace the vacuum oil regularly, and do not replace it with other oils

4. The pressing handle of the workbench should be refueled regularly to keep it lubricated.

5. In order to ensure the safety and normal operation of the machine, do not make the machine work beyond the design indicators of the machine.

6. When using maintenance parts not provided by our factory, you should consult our factory to avoid danger.

Note: Special oil for vacuum pumps, such as vacuum No. 1 oil for belt pumps, and N68# oil for direct-coupled pumps

 

 

List of random accessories

Name

Unit

Quantity

Remarks

Wrench

piece

2

17*19,12*14

Phillips screwdriver

piece

1


Allen wrench4,6

piece

2


Hexagon socket screw

piece

5

M6*25

Insurance tube

piece

2


Machine feet

set

8

Double  worktable

Machine feet

set

8

Double  worktable

Slotted screwdriver

piece

1


Inner hexagon

piece

1



 

                       梁旭名片

                      

Quality and Service are most important things for us  

                  If you have any problem,please let us know

 

 


Previous: 
Next: 

PRODUCT CATEGORY

CONTACT US

Add : No.1 Qianjin Road, Yaopu Town, Tieling County,Tieling City,Liaoning Province,China
Whatsapp:+8613166797961
E-mail : info@zhtmac.com
Please feel free to contact us with any questions, concerns, comments, or recommendations !
LIAONING ZHANHONGTU MACHINERY EQUIPMENT

QUICK LINKS

PRODUCTS CATEGORY

CONTACT US

   Add : No.1 Qianjin Road, Yaopu            Town, Tieling County,Tieling                  City,Liaoning Province,China
    Whatsapp : +86-15840529588
    E-mail : info@zhtmac.com

Copyright  2018  Shenyang Zhanhongtu Machinery Equipment Co.,Ltd. 
Sitemap